How to Make Solar Lights Brighter? 5 Easy Tips

Looking for how to make solar lights brighter? Here are five suggestions to help you!

Are the solar lights in your garden not as bright as you would like them to be? Don’t worry,

Because the brightness is not related to the solar light declared wattage, you shall give up the expectation that the higher the wattage solar light you buy, the much brighter solar light you will get.

Learn more about the brightness of solar lights by reading on.

How to Make Solar Lights Brighter?

Here are some tips you can use to make solar light brighter.

Cleaning the Solar Panel

One of the key parts of solar lighting is the solar panel. It is made of solar energy-absorbing cells that later transform that energy into electrical power for batteries.

It goes without saying that they must be exposed to as much sunlight as they can throughout the course of a day in order for solar light to function properly.

Checking the Batteries

Another essential part of solar garden lights is batteries. The energy from the sun is stored there, and it is this energy that drives the lights inside the solar fixture. Even though these batteries are usually built to last, that doesn’t guarantee a lifetime of use.

In fact, there are two things that you can do as far as batteries and solar light brightness is concerned: remove corrosion or replace the batteries altogether:

• Look up the location of the battery compartment in the user manual that came with your walkway lighting.
• Check for any white powder around the metal part of the battery housing after removing the batteries.
• Remove the powder from the battery and the housing using a brush or fine-grit sandpaper.
• Depending on how long it has been since you last changed your batteries, we do advise choosing to replace the battery with a new one rather than putting the old one back in.
• Make sure to wipe the battery housing and the batteries with a dry, clean cloth. If you put the batteries back in a humid housing, you run the risk of experiencing corrosion once more since corrosion is frequently caused by the solar lights being exposed to high levels of moisture and humidity.

Check the Position of the Solar Panel

It is important to make sure that the solar panel is in direct sunlight for as much of the day as possible. The light should be moved to a different location if a tree or other object is blocking the sun.

The solar panel may not be receiving enough direct sunlight if you have a sizable garden. If this is the case, consider moving the light to a different spot in your garden.

The panel can be easily moved as the seasons change and the vegetation expands, which may also help to increase its brightness. A panel that has been left clear to face the sun throughout the other seasons may quickly be obscured by summertime plant growth.

Hacking the Lights

This approach might be seen as a little extreme, but if you enjoy tinkering with circuit boards and the internal parts of your solar lights, it should be a lot of fun to try.

There is essentially a set procedure for this method, though the exact steps will vary depending on the solar lights you are using.

• Purchase a few extremely cheap solar lights that you shouldn’t mind permanently damaging and potentially losing money on if this experiment doesn’t work.
• Make sure to disconnect everything before taking apart your solar lights.
• Examine the battery that came with your solar lights (since the majority of them ought to have one already installed). Take note of the battery’s capacity and decide whether to replace it with one that is twice as powerful.
• Find the inductor’s location on the circuit board of the lights you are working with. Your lights’ brightness can be changed using the inductor. If you’re unsure which of these components is an inductor, feel free to do some research (the instruction manual for the lights may already contain this information).
• In order to eventually add additional light bulbs, modify the circuits. Using wire tighteners to fasten two lights together and then lining up the negative and positive ends should make this a fairly straightforward process.
• As this might be the case when making changes to the circuit board, adjust the inductor value if necessary.
• Reassemble the light parts to see if the lights have changed in brightness; given that the battery’s capacity has doubled and that you have now added an additional light, they ought to be twice as bright.

Removing Unnecessary Parts

Sometimes, a few minor adjustments that simply removing certain parts of your solar lights might make them brighter. Here are a few extra things you can do:

• Check for any plastic components that might prevent the panel and battery from receiving more light.
• If you want to recreate the conventional battery setup you’re accustomed to, think about making your own battery light holder out of two springs and gluing them together.
• Try to remove the top lid that is blocking sunlight from reaching the panel so that the rays can be absorbed as fully as possible. Keep in mind that the role of the lid is also to protect the interior components

Conclusion: How to Make Solar Lights Brighter

There are plenty of things you can do to brighten your solar lights, especially if we’re talking about items you’ve owned and used for a long time and are most likely dirty.

Therefore, proper maintenance is the key to brighter solar lighting. They’ll feel brand new if you keep them tidy, put them in good positions, and replace the batteries.

If necessary, you might have to relocate them or direct more light toward the solar panel, but hopefully these suggestions have made your solar lights brighter.

Also Read: How Long Do Solar Lights Last?

FAQs